Digital display of: start/onboard voltage, fill level of fresh/waste water. Programmable undervoltage. Main switch function, on/off switch (pump, ICC, etc.). Solar information of all MT solar controllers (from 2014 on).

The main tasks of the Victron battery monitor are to measure the charging and discharging currents and to calculate the state of charge and the remaining battery life. If certain limits are exceeded (such as excessive discharge), an alarm is sent out. The battery monitor can also exchange data with the Victron Global Remote. This also applies to the sending of alarms.

Displays onboard voltage and the fill level of fresh water/waste water/waste tank. Integrated main switch (16 A) and pump switch (10 A).

The Info Panel Pro monitors fresh water, waste water and waste tanks as well as the RV and starter battery in motorhomes – compact and with intuitive operation. It offers voltage displays for batteries, three-colour light bars for tank levels and main switches for the RV battery and fresh water pump. Installation and operating instructions are included and the low installation depth allows flexible installation. The device is protected against reverse polarity and overload, is de-energised when switched off and is suitable for 12 V batteries. With a current consumption of 0 – 50 mA and a main switch up to 16 A or a pump switch up to 10 A.

The solar remote display SF with LCD screen offers many features: it measures charging current (A) and system voltage (V), displays the solar power in a bar graph and shows the time and date. The energy counting function (Ah, Wh) allows you to read the capacity transferred to the battery. All values can be reset. Additionally, there is a programmable switching output. Please note: not suitable for MPPT solar controllers!

With integrated battery computer MT 4000 iQ plus fill level of fresh/waste water. Main switch function, on/off switch (pump, ICC, etc.). Solar information of all MT solar controllers (from 2014 on).

With integrated battery computer MT 4000 iQ plus fill level of fresh/waste water. Main switch function, on/off switch (pump, ICC, etc.). Solar information of all MT solar controllers (from 2014 on).

The DTU dongle expands the M12 series batteries with a Bluetooth interface. It offers significant advantages over internal solutions, as it can be installed away from the battery for better transmission and reception performance. Only one dongle is needed for multiple batteries. This eliminates mutual signal interference, establishing a connection only with the app. The DTU is not necessary when using displays with Bluetooth.

The VE.Direct Bluetooth Smart Dongle connects to a non-Bluetooth enabled VE.Direct Victron product, which can then be accessed via Bluetooth using the VictronConnect app to facilitate monitoring, setup and firmware updates.

The BMV-7xx is a high-precision battery monitor. The main function of a battery monitor is to calculate the ampere-hours consumed and the state of charge of a battery. The ampere-hours consumed are calculated by integrating the current flowing into or out of the battery. Only type BMV-702 and BMV-712 Smart monitor the centre point voltage.

An intelligent capacity indicator and voltmeter for BMS-controlled Super B battery systems. The available capacity contained in the battery system is displayed in %. The device is simply inserted in a round cutout and connected to the battery with four cables.Low current consumptionProgrammable alarm outputEasy to installWaterproof to the top

The smart battery measurement device can display voltage, current, charge status and remaining charge and discharge time so that you always know how long your battery is going to last. There are six available languages (DE, NL, EN, FR, IT, ES). Front display 2.4 inch TFT colour screen with 320 x 240 pixel resolution. Network protocol and connection: CAN bus/RJ11. Screwable fixing.

The BMV-7xx is a high-precision battery monitor. The main function of a battery monitor is to calculate the ampere-hours consumed and the state of charge of a battery. The ampere-hours consumed are calculated by integrating the current flowing into or out of the battery. Only type BMV-702 and BMV-712 Smart monitor the centre point voltage.

The smart battery measurement device can display voltage, current, charge status and remaining charge and discharge time so that you always know how long your battery is going to last. There are six available languages (DE, NL, EN, FR, IT, ES). Front display 2.4 inch TFT colour screen with 320 x 240 pixel resolution. Network protocol and connection: CAN bus/RJ11. Screwable fixing.

The main tasks of the Victron battery monitor are to measure the charging and discharging currents and to calculate the state of charge and the remaining battery life. If certain limits are exceeded (such as excessive discharge), an alarm is sent out. The battery monitor can also exchange data with the Victron Global Remote. This also applies to the sending of alarms.

The smart battery measurement device can display voltage, current, charge status and remaining charge and discharge time so that you always know how long your battery is going to last. There are six available languages (DE, NL, EN, FR, IT, ES). Front display 2.4 inch TFT colour screen with 320 x 240 pixel resolution. Network protocol and connection: CAN bus/RJ11. Screwable fixing.

The solar remote display SF with LCD screen offers many features: it measures charging current (A) and system voltage (V), displays the solar power in a bar graph and shows the time and date. The energy counting function (Ah, Wh) allows you to read the capacity transferred to the battery. All values can be reset. Additionally, there is a programmable switching output. Please note: not suitable for MPPT solar controllers!