Truma lamella insert LA.

The DC motor is an original Truma spare part. Please check the manufacturer’s part number.

The end piece EN-O is an original Truma spare part. Please check the manufacturer’s part number.

Truma lamella insert LA.

Side covers for cover frame Truma control panels.

The seal is an original Truma spare part. Please check the manufacturer’s part number.

The turning knob is an original Truma spare part. Please check the manufacturer’s part number.

The bushing is an original Truma spare part. Please check the manufacturer’s part number.

The DC motor is an original Truma spare part. Please check the manufacturer’s part number.

The thermostat plate is an original Truma spare part. Please check the manufacturer’s part number.

The complete wall flue set WK 24 for vehicle wall thicknesses up to 20 mm. Consists of: inner part of flue, 1 m exhaust pipe, 1 m feed pipe and clamps (without outer part of flue). In addition, a flue outer part WK is required.

The electronic system is an original Truma spare part. Please check the manufacturer’s part number.

Filter pads for gas filters.

The electronic system for Combi 4 (E) is an original Truma spare part. Please check the manufacturer’s part number.

For connecting the Truma E-Kit with the pipe VR 80.

The pushrod is an original Truma spare part. Please check the manufacturer’s part number.

Simplifies draining of the boiler, irrespective of the temperature in the installation compartment.

Spare part water parts for Truma electric boiler (05/04 – 12/14).

Spare part water parts Truma electric boiler (05/04 – 12/14)

The ignition pipe is an original Truma spare part. Please check the manufacturer’s part number.

The cover cap Ultraheat is an original Truma spare part. Please check the manufacturer’s part number.

Cable Harness for Combi 4 (E) and Combi 6 (E).

The piezo ignition set is an original Truma spare part. Please check the manufacturer’s part number.

Reduction of pipes from ø 72 mm to ø 49 mm.

The seal is an original Truma spare part. Please check the manufacturer’s part number.

The DC motor is an original Truma spare part. Please check the manufacturer’s part number.

Clamp for exhaust piping (wall thickness up to 40 mm).

Flue outer part for Truma Vario Heat.

Spare part for control panel CP plus Truma iNet System.

Spare part control panel Truma boilers B and BN 30 mbar series 3 (07/93 – 12/14)

The Truma G.7 high-pressure hose with SBS increases the safety of gas systems, fulfils legal standards and stops the flow of gas in the event of damage. Designed for use in the UK and Ireland, it supports safety when travelling and at the place of use.

For water heater up to 04/2002 and boiler BN series 3 up to 06/2006.

For maximum security on the road and at the campsite, Truma offers high-pressure hoses equipped with hose rupture protection (SBS). They meet all legal requirements for running gas systems while driving but are also suitable for stationary use. If the hose is damaged, the protection is triggered and stops the gas flow.

The injector is an original Truma spare part. Please check the manufacturer’s part number.

For the air distribution pipe of E-heaters, ø 65 mm and ø 72 mm

The heating rod is an original Truma spare part. Please check the manufacturer’s part number.

Model 2 + 3

Control panel for boiler.

Spare part for Truma boilers B and BN 30 mbar series 3 (07/93 – 12/14).

The AE 5 exhaust pipe ensures safe exhaust gas discharge.

The flame control electrode is an original Truma spare part. Please check the manufacturer’s part number.

Clamp ÜS for pipe ÜR.

For water heaters built since 2002.

Control panel cable Ultraheat S3002, S3004, S5002 and S5004.

Burner Set for Combi 4 (E) and Combi 6 (E).

At a temperature of 0 °C, tiny droplets of ice or propane hydrate can form in the regulator due to traces of water in liquid gas. This reduces or stops the gas supply.The regulator heater EisEx prevents the formation of ice droplets with electrical heating. EisEx ensures trouble-free gas supply even in winter.

Complete wall flue set WK 64 L for vehicle wall thicknesses up to 40 mm. Consists of: inner part of flue, 1 m exhaust pipe, 1 m feed pipe and clamps (without outer part of flue). In addition, a flue outer part WK is required.

ø 65/72 mm