Replace the defective or worn-out lid spring of your Clesana toilet.

Faeces and toilet waste are hygienically sealed in high barrier film. Odour-proof storage for several days is possible. One piece of film liner is sufficient for approx. 40 bags.

Spare part for Clesana toilets.

Control panel including electronic system and connection cable.

With the help of the conversion kit, you can easily convert the standard soft-close lid of your Clesana C1 into a lid with a magnetic hinge. This allows you to completely remove the lid from the seat, especially in tight installation spaces. The conversion takes approx. 30 minutes. Maximum comfort even in small spaces Easy to clean due to ideal accessibility Cost-effective DIY solution Contents: 4 hinges with neodymium magnets, 1 drilling template and assembly instructions The toilet seat is not included!

Replacement magnet for your Clesana toilet seat.

Minimise standby power! The Clesana Power Management can be used as a pure relay. The standby power is nearly 10 times lower than that of the Clesana C1 (30 mA). It is very easy to control via a 12 V permanent positive cable. Another advantage is that in the future, you always have the option to expand the Power Management to operate via a backup battery. Made in Germany.Relay with low power consumptionRetrofittable to backup batteryScope of delivery: Clesana Power Management by VotronicNot included: Power Management cable set to Clesana C1, Power Management cable set to backup battery, backup battery

The PTFE (Teflon) tapes are positioned over the welding wire and prevent the hot polymer from adhering to the welding jaws during the welding process. To maintain the quality of the welds, you have to change the two tapes after approx. 1500 welds.

The anti-slip is the ideal addition for the Clesana C1: it prevents unnecessary film consumption, ensures that the bags stay compact even with multiple uses and saves up to 80 cm of liner per cassette. Retrofitting is straightforward and provides a sustainable solution against slipping – for maximum efficiency and less waste.

This surface-mounted housing is specially designed for the control panel of the Clesana C1 toilet. It provides a secure and clean installation of the panel on the surface. The housing is equipped with 4 holes for easy installation and cable routing.Scope of delivery: surface-mounted housing (without control panel)

Connection cable for your Clesana control panel.

Made of special sailcloth. Protects against water ingress caused by e.g. jet water during showering. Sewn to fit precisely, with high hydrostatic head.

Spare part for Clesana toilets.

For free placement of the C1 in the room and for special retrofitting.

The film cassette for Clesana toilets is the matching original spare part for all models of the innovative waterless dry toilet.

Efficient energy supply for on the goThe Clesana power management system enables quick and easy electrical installation and ensures even greater autonomy in mobile use. This innovative solution combines the functions of a relay and a DC/DC charger, ensuring that the Clesana C1 is optimally supplied.Thanks to the pre-assembled cables, the connection between the Clesana C1 and a support battery can be established effortlessly. The control input regulates the current flow to the Clesana C1, while the power management supplies the support battery with 2 A charging current in standby mode. Control is achieved via a 12 V permanent positive cable, ensuring reduced power consumption. Should the RV battery fail, the Clesana C1 remains operational via the support battery.Manufactured in Germany, the Clesana power management system impresses with the highest quality and reliability.Advantages:Easy electrical installation through pre-assembled cablesAutonomous power supply for greater independenceEfficient energy management with optimised charging functionScope of delivery:Clesana power management by VotronicCable set power management to Clesana C1Cable set power management to support batteryNot included in the scope of delivery: support battery

The first portable, waterless toilet with bag sealing. Easy to install and retrofit. Spend the night away from campsites without giving up the convenience and cleanliness they provide – thanks to "thermal pressure sealing". A key objective in the development of the C1 was to ensure excellent environmental compatibility without compromising on hygiene. With the C1, you do not need any sanitary additives and save water at the same time. Swiss Made.Power consumption standby: 0.28 WPower consumption sealing process: 0.55 WhPlease note: supplied with accessories for initial equipment.Scope of delivery:1 barrier film liner1 pack of super absorber

This drawer without a front panel is a spare part for your Clesana dry toilet. Perfectly suitable if the existing drawer is damaged or needs replacing. This ensures that the Clesana toilet remains reliable in use.

The first portable, waterless toilet with bag sealing. Easy to install and retrofit via L adapter. Spend the night away from campsites without giving up the convenience and cleanliness they provide – thanks to "thermal pressure sealing". A key objective in the development of the C1 was to ensure excellent environmental compatibility without compromising on hygiene. With the C1, you do not need any sanitary additives and save water at the same time. Swiss Made.Power consumption standby: 0.28 WPower consumption sealing process: 0.55 WhPlease note: Supplied with accessories for initial equipment.Scope of delivery:1 barrier film liner1 pack of super absorber

The 30 A fuse (PCB) is an important spare part for the safe operation of the Clesana C1 dry toilet. It protects the electronic control board (PCB) from overcurrent and ensures that all functions of the toilet run reliably and securely.

For easy retrofitting of the C1, e.g. on the basis of the Thetford C220 & C260 series.

Complete body with welding unit, mechanics and electronics for easy replacement of an installed body.

Simply place a sachet in the toilet compartment before it is sealed to absorb liquids. The film made from bio-plastic (PVA) dissolves automatically and the granules absorb up to 400 ml of liquid.

The cover is plugged into the drawer container.