For fastening with clamping holders, where the height adjustment is made in an unloaded state by loosening a clamping device.

The Safety Ball is used to occupy the ball head space of the WS 3000. This provides additional protection. Also suitable for all other ball couplings.

Zinc-coated clamp holder for 48 mm pipes, without installation material. Supports up to 250 kg. Steel base plates with 2 holes, standard toggle clamp, galvanised.

Handle for WS 3000, black

Friction lining for coupling WS 3000 (V1) built until 07/2002.

Friction lining clip set for coupling WS 3000 (V1) built since 08/2002.

The anti-theft device ROBSTOP WS 3000 provides protection against:Unauthorised disconnection of trailers from towing vehicleConnection of the trailer to another towing vehicleBall coupling being dismantled from the tow bar Accidental disconnection of the trailer during drivingIf ROBSTOP WS 3000 is being used with a disconnected trailer, the ball opening can be closed before using the provided Safety Ball.ROBSTOP WS 3000 PLUS fulfils the requirements of SCM/Netherlands and SoldSecure Gold (GB). These requirements are set by the respective insurance companies of those countries.Simple handlingHigh-quality alloyed steel with cylinder lockWith Safety Ball

Crank for jockey wheels.

The zinc-coated clamp holder fixing is perfect for 70 mm square tubes, providing a secure hold with a bearing load of up to 250 kg. Thanks to the galvanisation, it is weatherproof and durable. Ideal for trailers or transport solutions.

Spare wheel for jockey wheels ST, K and VK made of solid rubber.

Plastic spare wheel for jockey wheels ST, K and VK.

Prevents accidental disconnection of jockey wheels ST 48 while on the road.Easy to retrofit, install and operateDurableTÜV-approved

Coupling indicator for WS 3000 from 08/09

Maxi Soft Buffer coupling protection for WS 3000 from 08/09 onwards.

For overrun devices of the WS 3000 chassis.

for WS 3000 until 07/02

The scale of the indicator was designed so that the value indicated corresponds approximately to the load on the ball coupling at the front. The user can read off the trailer load easily to ensure safety when driving with a caravan. The topic of bearing load has gained even more importance due to the 100 km/h speed control regulations. In addition, the spring-suspended wheel fork makes manoeuvring in an uncoupled state easier as the inner tube acts as a shock absorber. No TÜV registration required. Scale of 0 – 125 kg.

Spare tube for jockey wheels, available in two sizes.

For supporting the trailer. The support leg is attached to the rear of the trailer together with the clamp holder (116/001). Lowering the support leg prevents the trailer from tilting backwards.

The anti-theft device ROBSTOP WS 3000 provides protection against:Unauthorised disconnection of trailers from towing vehicleConnection of the trailer to another towing vehicleBall coupling being dismantled from the tow bar Accidental disconnection of the trailer during drivingIf ROBSTOP WS 3000 is being used with a disconnected trailer, the ball opening can be closed before using the provided Safety Ball.ROBSTOP WS 3000 PLUS fulfils the requirements of SCM/Netherlands and SoldSecure Gold (GB). These requirements are set by the respective insurance companies of those countries.Simple handlingHigh-quality alloyed steel with cylinder lockWith Safety Ball

Spare wheel for jockey wheels ST, K and VK.

Spare wheel pneumatic tyre with steel rim. Perfect for rough and wet conditions.

Angle top ABD for WS 3000, blue

Toggle M 12 x 30 zinc-coated.

The Ball Cap provides protection for the ball coupling and your shin.

Coupling indicator to check the fit of the ball of the vehicle in the WS 3000 after coupling, more accurate wear indication for testing the condition of the friction elements and the ball of the vehicle, significantly increased handle for maximum stability during use, optimal seat of the Maxi-Soft buffer by new mounting points on the top and bottom of the housing of the WS 3000.The only one of its kind that reached the critical speed of 130 km/h in France without any side motion of the trailer. Had the best attenuation and the highest damping factor during lurching and pitching movements.
Single-lever system for all functions:- Connecting – disconnecting- Stabilising – destabilising- Locking – unlockingCoupling is no problem even for vehicles with an externally mounted spare wheel and only a small space between bumper and ball couplingMaxi-Soft buffer protects legs and bumperPlenty of space between handle and drawbarAll friction linings are exchangeable due to the Clip systemExtremely slender design gives unrestricted ball shaft spaceWear indicator easily readableLow tare weight with 3 t towing capacityBearing load up to 150 kgDrawbar ø 35, 40, 45, 46, 50 mmEG-approval no. 00-0065 e1No registration required!Retrofittable to all trailers with drawbar connections between ø 35 – 50 mm, cross or parallel fittingScope of delivery:WS 3000-D+ZSafety BallBall CapRobstop WS 3000

The zinc-coated clamp holder fixing fits 70 mm drawbar tubes and secures up to 250 kg. Ideal for round tubes, robust and durable.

More track fidelity and safety The WS 3000 stabilisation couplings for braked trailers up to 3000 kg, featuring specially developed friction elements, are pressed axially against the vehicle's ball under high spring pressure, creating enormous stability for the combination. This permanently increases the critical speed at which a combination becomes unstable and starts to sway by up to 30%. The WS 3000 meet the ISO 11555-1 standard and are thus approved stabilisation devices for the 100 km/h regulation. Product line: Premium Professional Your advantages: Reduces swaying and pitching movements of the trailer to prevent emergency situations Single-lever system for all functions for quick coupling EU approval, therefore no TÜV entry required Delivery includes mounting accessories Coupling and wear indicator More clearance to the vehicle rear Integrated soft dockIncl. safety ball and ball capTowing capacity: 3000 kg; vertical load: 150 kg; ball diameter: 50 mm

For fastening with clamping holders, where the height adjustment is made in an unloaded state by loosening a clamping device.

Hole spacing: 200/160 mm wide. Total length with rail: 575 mm. Extended length: 450 mm.